View PL613-05-XXXSIR_1296420.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(Preliminary)
1.8V-3.3V PicoTreo TM , 3-PLL, 200MHz, 5 Output Clock IC
FEATURES
Designed for PCB space savings with 3 low-power Programmable PLLs and up to 5 clock outputs. Low-power consumption (<10A when PDB is activated) Output Frequency: o <133MHz @ 1.8V operation o <166MHz @ 2.5V operation o <200MHz @ 3.3V operation Input Frequency: o Fundamental Crystal: 10MHz - 50MHz o Reference Input: 1MHz - 200MHz Programmable I/O pins can be configured as Output Enable (OE), Power Down (PDB) inputs, Configuration Select (CSEL) or Clock outputs. Disabled outputs programmable as HiZ or Active Low Two distinct configurations selectable with CSEL (MSOP-10L Only) Single 1.8V ~ 3.3V, 10% power supply Operating temperature range from -40C to 85C Available in GREEN/RoHS compliant 8-pin SOP or 10-pin MSOP packages.
DESCRIPTION
The PL613-05 is an advanced triple PLL design based on PhaseLink's PicoPLL TM , world's smallest programmable clock, technology. This flexible programmable architecture is ideal for high performance, low-power, low-cost applications. When using the power down (PDB) feature the PL613-05 consumes less than 10 A of power, while its Configuration Select (CSEL) function allows switching of 2 programmable configurations. Besides its small form factor and 3 or 5 outputs that can reduce overall system costs, the PL613-05 offers superior phase noise, jitter and power consumption performance.
BLOCK DIAGRAM
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 www.phaselink.com Rev 7/2/07 Page 1
(Preliminary)
1.8V-3.3V PicoTreo TM , 3-PLL, 200MHz, 5 Output Clock IC
PIN CONFIGURATION
XIN/FIN CLK2/OEM^/PDB^ VDD CLK0 1 PL613-05 SOP-8L
^ Denotes internal pull up
8 7 6 5
XOUT VDD CLK1 GND
GND CLK4/CSEL^ CLK2/OEM^/PDB^ VDD CLK3
1 2 3 4 5 PL613-05
10 9 8 7 6
XIN/FIN XOUT VDD CLK1 CLK0
2 3 4
MSOP-10L
PACKAGE PIN ASSIGNMENT
Name GND CLK4/CSEL CLK2/OEM/PDB VDD CLK3 CLK0 CLK1 XOUT XIN/FIN Package Pin # MSOP-10L SOP-8L 1 2 3 4, 8 5 6 7 9 10 5 2 3, 7 4 6 8 1 Type P B* B* P O B* O O I GND connection - Programmable Clock (CLK4) output or - Configuration Switching input - Programmable Clock (CLK2) output, or - Output Enable Master (OEM) for all clock outputs, or - Power Down mode (PDB) input VDD connection Programmable Clock (CLK3) output Programmable Clock (CLK0) output Programmable Clock (CLK1) output Crystal output pin. Do Not Connect when using FIN Crystal or Reference Clock input Description
* Note: All bidirectional buffers (I/Os) incorporate an internal 60K pull up resistor except when PDB mode is used. In configurations that use PDB, the PDB pin will have a 10M pull up resistor.
KEY PROGRAMMING PARAMETERS
CLK[ 0:4 ] Output Frequency CLK[0] F VCO2 / P CLK[1,2] F VCOx / (P*(1,2,4,8)) or F REF / (P*(1,2,4,8)) CLK[3] F VCO2 / (P*(1,2,4,8)) or F REF / (P*(1,2,4,8)) CLK[4] F VCO3 / P or F REF / P Where F VCO = F REF * M / R M = 11 bit R = 8 bit P = 5 bit (Odd/Even Divider) Output Drive Strength Each output has three optional drive strengths to choose from. They are: Low: 4mA Std: 8mA (default) High:16mA Programmable Input/Output Most pins are multi-function I/Os and can be configured as: OEM - (Master OE controlling all outputs) CSEL - (Device Configuration Switching) PDB - (Power Down) CLK[0:4] - (Output) HiZ or Active Low disabled state
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 www.phaselink.com Rev 7/2/07 Page 2
(Preliminary)
1.8V-3.3V PicoTreo TM , 3-PLL, 200MHz, 5 Output Clock IC
FUNCTIONAL DESCRIPTION
The PL613-05 is a highly featured, very flexible, advanced triple PLL design for high performance, low-power applications. The device accepts a low-cost fundamental crystal input of 10MHz to 50MHz or a reference clock input of 1MHz to 200MHz and is capable of producing 3 (SOP-8L) or 5 (MSOP-10L) distinct output frequencies up to 200MHz. All 3-PLLs are fully programmable, with a total of four, 5-bit Post VCO, Odd/Even (patent pending) `Pcounter' dividers with additional 1, 2, 4 or 8 `Post P-counter' dividers to allow generating the most demanding frequencies easily. The outputs can be programmed to deliver the generated frequencies from the PLLs, or the reference input. Each bidirectional feature pin (I/O) on the PL613-05 incorporates a 60K pull up resistor (10M for PDB function) and can be configured to perform various functions. Usage of various design features of these products is mentioned in the following paragraphs. PLL Programming The three PLLs in PL613-05 are fully programmable. Each PLL is equipped with an 8-bit input frequency divider (R-Counter) and an 11-bit VCO frequency feedback loop (M-Counter) divider. The three PLL outputs are transferred to four 5-bit post VCO, Odd/Even (patent pending) dividers (P-Counter), as shown in the above diagrams. In addition, there are three optional (/1, /2, /4 or /8) post P-Counter dividers, that can further divide the VCO frequencies. In general, the PLL output frequency is determined by the following formula F OUT = (F REF *M) / (R*P) For output calculations, please note that `P' includes the `P' counter bits plus the additional optional (/1, /2, /4 or /8) dividers, if used. CLKx (Clock Outputs) There are a maximum of 3 (SOP-8L) or 5 (MSOP-10L) outputs available on the PL613-05. Clock output frequencies can be configured as follows: CLK[0] F VCO2 / P CLK[1,2] F VCOx / (P*(1,2,4,8)) or F REF / (P*(1,2,4,8)) CLK[3] F VCO2 / (P*(1,2,4,8)) or F REF / (P*(1,2,4,8)) CLK[4] F VCO3 / P or F REF / P Each output can be programmed with a 4mA, 8mA, or 16mA drive strength. The maximum output frequency is 200MHz @ 3.3V, 166MHz @ 2.5V or 133MHz @ 1.8V. OEM (Master Output Enable) One pin can be configured to be a single Master OE (OEM) input pin that controls all the outputs of the PL613-05. In addition the state of the disabled outputs can be programmed to float (Hi Z) or Active `0'. The OEM pin incorporates a 60k pull up resistor for normal operating condition. The logic for OEM is shown below: OEM OE Type Osc PLL Output Pin (Programmable) 0 (Default) On On Hi Z 0 1 On On Active `0' 1 Normal Operation (Default)
Note: Typical enable time is 10ns.
Power-Down Control (PDB) When activated, PDB `Disables all the PLLs, the oscillator circuitry, counters, and all other active circuitry. PDB activation disables all outputs and the IC consumes <10A of power. The PDB input incorporates a 10M pull up resistor for normal operating condition. The PDB feature can be programmed to allow the output to float (Hi Z), or to operate in the `Active low' mode. The logic for PDB is shown below: PDB PDB Type Osc PLL Output Pin Program 0 0 (Default) Off Off Hi Z 1 1 Off Off Active `0' Normal Operation (Default)
Note: Typical enable time is <2ms.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 www.phaselink.com Rev 7/2/07 Page 3
(Preliminary)
1.8V-3.3V PicoTreo TM , 3-PLL, 200MHz, 5 Output Clock IC
On-The-Fly Configuration Switching (CSEL) The PL613-05 can be programmed to allow switching between 2 different configurations, allowing for changes in the output frequency and other feature changes. Many applications (i.e. video/audio) can use the same design footprint, but allow for configuration switching, adhering to various standards. CSEL is used to make the switching selection. This pin incorporates a 60k pull up resistor for normal operating condition. The logic for configuration switching of the programmed parts is shown below: CSEL 0 1 Programmed Configuration 0 1(Default)
Note: Typical enable time is 100s.
LAYOUT RECOMMENDATIONS
The following guidelines are to assist you with a performance optimized PCB design:
Signal Integrity and Termination Considerations
- Keep traces short! - Trace = Inductor. With a capacitive load this equals ringing! - Long trace = Transmission Line. Without proper termination this will cause reflections ( looks like ringing ). - Design long traces as "striplines" or "microstrips" with defined impedance. - Match trace at one side to avoid reflections bouncing back and forth.
Decoupling and Power Supply Considerations
- Place decoupling capacitors as close as possible to the VDD pin(s) to limit noise from the power supply - Multiple VDD pins should be decoupled separately for best performance. - Addition of a ferrite bead in series with VDD can help prevent noise from other board sources - Value of decoupling capacitor is frequency dependant. Typical values to use are 0.1F for designs using crystals < 50MHz and 0.01F for designs using crystals > 50MHz.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 www.phaselink.com Rev 7/2/07 Page 4
(Preliminary)
1.8V-3.3V PicoTreo TM , 3-PLL, 200MHz, 5 Output Clock IC
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 www.phaselink.com Rev 7/2/07 Page 5
(Preliminary)
1.8V-3.3V PicoTreo TM , 3-PLL, 200MHz, 5 Output Clock IC
ELECTRICAL SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS PARAMETERS Supply Voltage Range Input Voltage Range Output Voltage Range Soldering Temperature (Green package) Data Retention @ 85C Storage Temperature Ambient Operating Temperature* TS 10 -65 -40 150 85 SYMBOL V DD VI VO MIN. -0.5 -0.5 -0.5 MAX. 4.6 V DD +0.5 V DD +0.5 260 UNITS V V V C Year C C
Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above the operational limits noted in this specification is not implied. *Operating temperature is guaranteed by design. Parts are tested to commercial grade only.
AC SPECIFICATIONS
PARAMETERS Crystal Input Frequency (XIN) Input (FIN) Frequency Input (FIN) Signal Amplitude Input (FIN) Signal Amplitude @ V DD =3.3V @ V DD =2.5V @ V DD =1.8V Internally AC coupled (High Frequency) Internally AC coupled (Low Frequency) 3.3V <50MHz, 2.5V <40MHz, 1.8V <15MHz @ VDD =3.3V Output Frequency Settling Time Output Enable Time VDD Sensitivity Output Rise Time Output Fall Time Duty Cycle Period Jitter, Pk-to-Pk* (10,000 samples) @ VDD =2.5V @ VDD =1.8V At power-up (after VDD increases over 1.62V) OE Function; Ta=25 C, 15pF Load PDB Function; Ta=25 C, 15pF Load Frequency vs. VDD +/-10% 15pF Load, 10/90% VDD, High Drive, 3.3V 15pF Load, 90/10% VDD, High Drive, 3.3V PLL Enabled, @ VDD /2 Input 16MHz fundamental mode crystal, all outputs at 40MHz, 10pF Load, with capacitive decoupling between V DD and GND. 45 -2 1.2 1.2 50 100 0.9 0.1 1 CONDITIONS Fundamental Crystal MIN. 10 TYP. MAX. 50 200 166 133 VDD VDD 200 166 133 2 10 2 2 1.7 1.7 55 120 ms ns ms ppm ns ns % ps MHz Vpp Vpp MHz UNITS MHz
* Note: Jitter performance depends on the programming parameters.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 www.phaselink.com Rev 7/2/07 Page 6
(Preliminary)
1.8V-3.3V PicoTreo TM , 3-PLL, 200MHz, 5 Output Clock IC
DC SPECIFICATIONS
PARAMETERS Supply Current, Dynamic, Loaded CMOS Outputs Supply Current, Dynamic, Loaded CMOS Outputs Supply Current, Dynamic, Loaded CMOS Outputs Supply Current Operating Voltage Output Low Voltage Output High Voltage Output Current, Low Drive Output Current, Standard Drive Output Current, High Drive SYMBOL I DD I DD I DD I DD V DD V OL V OH I OSD I OSD I OHD I OL = +4mA Std Drive I OH = -4mA Std Drive V OL = 0.4V, V OH = 2.4V V OL = 0.4V, V OH = 2.4V V OL = 0.4V, V OH = 2.4V V DD - 0.4 4 8 16 CONDITIONS All outputs @ 20MHz 10pF Load All outputs @ 20MHz 10pF Load All outputs @ 20MHz 10pF Load When PDB=0 All outputs @ 20MHz 10pF Load, V DD = 3.3V 1.62 MIN. TYP. 15 11 8.5 MAX. 21 16 11 <10 3.63 0.4 UNITS mA mA mA A V V V mA mA mA
CRYSTAL SPECIFICATIONS
PARAMETERS Fundamental Crystal Resonator Frequency Crystal Loading Rating Maximum Sustainable Drive Level Operating Drive Level Metal Can Crystal Small SMD Crystal Shunt Capacitance ESR Max Shunt Capacitance ESR Max C0 ESR C0 ESR 30 5.5 50 2.5 80 SYMBOL F XIN C L (xtal) MIN. 10 15 100 TYP. MAX. 50 UNITS MHz pF W W pF pF
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 www.phaselink.com Rev 7/2/07 Page 7
(Preliminary)
1.8V-3.3V PicoTreo TM , 3-PLL, 200MHz, 5 Output Clock IC
PACKAGE DRAWINGS (GREEN PACKAGE COMPLIANT)
MSOP-10L Dimension in MM Min. Max. 0.86 1.06 0.05 0.15 0.81 0.91 0.17 0.25 0.1 0.2 3.00 BSC 3.00 BSC -5.08 0.43 0.63 0.50 BSC
Symbol A A1 A2 b C D E H L e
E
H
D
A2 A A1 e b C L
SOP-8L Symbol A A1 A2 b C D E H L e Dimension in MM Min. Max. 1.35 1.75 0.10 0.25 1.25 1.50 0.33 0.53 0.19 0.27 4.80 5.00 3.80 4.00 5.80 6.20 0.40 0.89 1.27 BSC
E
H
D
A2 A A1 e b C L
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 www.phaselink.com Rev 7/2/07 Page 8
(Preliminary)
1.8V-3.3V PicoTreo TM , 3-PLL, 200MHz, 5 Output Clock IC
ORDERING INFORMATION (GREEN PACKAGE COMPLIANT)
For part ordering, please contact our Sales Department: 47745 Fremont Blvd., Fremont, CA 94538, USA Tel: (510) 492-0990 Fax: (510) 492-0991 PART NUMBER The order number for this device is a combination of the following: Part number, Package type and Operating temperature range
PL613-05-XXX X X X
PART NUMBER 3 DIGIT ID Code * (will be assigned at programming time) PACKAGE TYPE M=MSOP-10L S=SOP-8L NONE= TUBE R=TAPE and REEL TEMPERATURE C=COMMERCIAL (0C to 70C) I= INDUSTRIAL (-40C to +85C)
* PhaseLink will assign a unique 3-digit ID code for each approved programmed part number.
Part Number/Order Number PL613-05-XXXMC PL613-05-XXXMC-R PL613-05-XXXSC PL613-05-XXXSC-R
Marking J3XXX J3XXX J3XXX J3XXX
Package Option 10-Pin MSOP (Tube) 10-Pin MSOP (Tape and Reel) 8-Pin SOP (Tube) 8-Pin SOP (Tape and Reel)
Note: `XXX' designates marking identifier that, at times, could be independent of the part number. Please consult your PhaseLink sales representative for marking information.
PhaseLink Corporation, reserves the right to make changes in its products or specifications, or both at any time without notice. The information furnished by Phaselink is believed to be accurate and reliable. However, PhaseLink makes no guarantee or warranty concerning the accuracy of said information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY: PhaseLink's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of PhaseLink Corporation.
Solder reflow profile available at www.phaselink.com/QA/solderingGreen.pdf
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991 www.phaselink.com Rev 7/2/07 Page 9

▲Up To Search▲

Price & Availability of PL613-05-XXXSIR

	To Download PL613-05-XXXSIR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .